Guide

Jet Grouting and Deep Soil Mixing: When Standard Underpinning Isn't Enough

Wagga Foundation Repairs is an independent referral service and does not perform or contract for the advertised work. Your enquiry may be referred to an independent contractor. Where licensing is required, the contractor's identity and licence details will be provided before you accept a quotation or enter a contract.

Jet grouting and deep soil mixing are ground improvement methods: instead of carrying a footing down to firmer ground, as piers and concrete underpinning do, they mix cement into the weak soil itself to make columns or blocks of stronger “soilcrete”. They are specialist, engineer-designed techniques more often used on civil and commercial work, and for an ordinary house with one corner that has dropped, conventional underpinning or restumping is the usual answer. A geotechnical engineer decides whether a site needs anything more.

What is jet grouting?

Keller, a ground engineering contractor, describes jet grouting on its own technical page as using “high velocity fluid jets to construct cemented soil, or Soilcrete” (Keller Australia, Jet grouting). An injection tool on the end of a drill stem is advanced to the treatment depth; jets of cement grout, sometimes with water and air, then erode the surrounding soil and mix it with grout as the stem is rotated and raised in a controlled way. The result can be panels, full columns or partial columns.

Keller lists underpinning foundations and excavation support among its common uses, and says the method can work in limited spaces and around buried obstacles such as services, and can target a soil layer at depth without treating the soils above. It also notes that because the process erodes soil, cohesionless soils are typically more erodible than cohesive (clay) soils, and that projects usually start with test columns to prove diameter and strength. Those are a contractor’s descriptions of its own technique.

What is deep soil mixing?

Keller’s page on wet soil mixing says it is “also known as deep soil mixing” and improves weak soils by mechanically mixing them with a cementitious binder slurry (Keller Australia, Wet soil mixing). A drill advances a mixing tool while slurry is pumped through it, with more mixing as the tool is withdrawn, to form single columns, overlapping rows or a whole stabilised block. Keller lists support of strip, pad and slab foundations among its uses, alongside road embankments, bridge supports and excavation support.

The difference, in short: jet grouting erodes and mixes soil with high-pressure jets; deep soil mixing stirs it mechanically. Which one, if either, suits a site depends on the soil profile, depth and access, and that is an engineering decision.

How they differ from standard underpinning

Conventional underpinning, whether screw piles or mass concrete, assumes there is firmer bearing ground at a reachable depth and transfers the footing’s load down to it. Resin injection fills voids and stiffens soil close under a slab or footing. Ground improvement treats a volume of weak soil so that it can carry load itself.

That matters on what AS 2870 and the National Construction Code call problem sites. The NCC Housing Provisions describe class P sites as including soft soils such as soft clay, silt or loose sand, landslip, mine subsidence, collapsing soils, and sites that cannot otherwise be classified, and require sites classed H, E or P to follow AS 2870 (ABCB, NCC 2022 Housing Provisions Part 4.2). A site’s class comes from a geotechnical report, not from a suburb name.

When might an engineer consider ground improvement?

Situations where the firm layer is deep or unreliable, or where digging is risky, for example:

  • a broad zone of loose or poorly compacted fill, rather than one dropped corner
  • deep soft layers, where piers would need to go a long way to reach bearing
  • tight access, or buried services and a neighbouring building close to the work
  • larger commercial or multi-unit sites; see the commercial and warehouse guide

For seasonal clay movement, a failing stump line or a single settled corner, the foundation inspection and engineer’s report will usually specify conventional methods.

What does it cost?

No published Australian cost guide found prices jet grouting or deep soil mixing for houses, so this site gives no figure. Price depends on the volume treated, depth, soil, access, the geotechnical investigation and design, and test columns. Published ranges for conventional underpinning are in the underpinning cost guide. Whatever the method, a contractor licence is needed for residential underpinning and piering valued at more than $5,000 including GST (NSW Government, Underpinning and piering work).

Request a quote to have an independent licensed contractor inspect, with an engineer brought in where the site needs one.

Frequently asked questions

Does a house with cracking on clay need jet grouting?

Usually not. Seasonal clay movement and a dropped corner are what conventional underpinning, restumping and moisture correction address; ground improvement is for weak ground across a wider area or at depth.

Who decides whether ground improvement is needed?

A geotechnical or structural engineer, from a soil investigation such as boreholes or test pits, not from a visual inspection alone.

How does jet grouting compare with resin injection?

Both inject material into the ground, but resin injection works close under a slab or footing, while jet grouting builds cement-soil columns or panels from grout and the soil itself, often at depth (Keller Australia).

Sources

Last reviewed 15/11/2026. How these pages are researched and corrected.

More guides

Lean-To and Verandah Foundation Failure in Wagga Wagga: Causes and Costs

Why lean-tos and verandahs move separately from the house, the signs, the repair order, NSW rules and published…

View

Foundation Repair While Living in the House: What's Realistic

Can you stay home during underpinning? What is usually disrupted, services and Before You Dig Australia, when moving…

View

Mudjacking vs Polyurethane Foam: Slab Lifting in Wagga Wagga

Mudjacking and polyurethane foam lifting compared for sunken paths, driveways and slabs: how each works, published…

View

More on this topic

Request a quote

Tell us about the job and an independent local contractor can quote it.

Get a Quote